搅拌一体机主要由底盘系统、液压传动系统、搅拌罐体、出料系统、清洗系统、副车架、操纵系统、托轮系统、进料系统、电路系统十个部分组成。下面来分析下搅拌一体机的四项工作原理。

The mixer is mainly composed of ten parts: chassis system, hydraulic transmission system, mixing tank, discharging system, cleaning system, subframe, control system, supporting wheel system, feeding system and circuit system. Next, we will analyze the four working principles of the mixer.

搅拌一体机搅拌功能原理：

Mixing function and principle of the mixer:

取力器将发动机的动力通过小传动轴带动液压泵液压马达转动，经过减速机带动搅拌桶转动。在运输混凝土的途中，需要保持搅拌罐每分钟1-3转的低速转动，以保证混凝土的匀质,同时防止混凝土的离析,称为搅动（俗称搅拌）。

The power take-off drives the power of the engine through the small transmission shaft to drive the hydraulic motor of the hydraulic pump to rotate, and drives the mixing drum to rotate through the reducer. During the transportation of concrete, it is necessary to keep the mixing tank rotating at a low speed of 1-3 revolutions per minute to ensure the uniformity of concrete and prevent concrete segregation, which is called stirring (commonly known as mixing).

搅拌一体机装料功能原理：

Loading function and principle of the mixer:

搅拌一体机在装混凝土的时候搅拌罐转速较快，速度为每分钟6-10转，混凝土通过装料系统从筒口导管进入搅拌筒，并在螺旋叶片引导下，流向搅拌筒的中下部。注意：装料时与运输过程中罐体的转动方向应保持一致，否则在运输过程中会将混凝土卸出。

When the mixing machine is loading concrete, the mixing tank rotates at a fast speed of 6-10 revolutions per minute. The concrete enters the mixing tank from the tube at the barrel mouth through the charging system and flows to the middle and lower parts of the mixing tank under the guidance of spiral blades. Note: The rotation direction of the tank during loading and transportation shall be consistent, otherwise the concrete will be unloaded during transportation.

搅拌一体机卸料功能原理：

Discharging function and principle of the mixer:

搅拌一体机在卸料时，发动机将动力通过取力器，液压泵，减速机等传输到搅拌罐，带动罐体转动，速度为3-14转/分；混凝土在叶片螺旋运动的顶推作用下向筒口方向移动，经过搅拌一体机的卸料斗卸出。此时罐体的转动方向与进料时的方向相反。

When the mixer is discharging, the engine transmits power to the mixing tank through the power take-off, hydraulic pump, reducer, etc., driving the tank to rotate at a speed of 3-14 rpm; The concrete moves towards the cylinder mouth under the pushing action of the spiral movement of the blade and is discharged through the discharge hopper of the mixing machine. At this time, the rotation direction of the can body is opposite to the feeding direction.

搅拌一体机清洗功能原理：

Cleaning function and principle of the mixer:

通过制动系统的储气筒给水罐加压，水流经过加压清洗搅拌罐系统，装料口，卸料系统等。

The water tank is pressurized through the air reservoir of the braking system, and the water flows through the pressurized cleaning mixing tank system, charging port, unloading system, etc.

搅拌一体机的四项工作原理分析就到这里了，如果您想好好顺利全且保障的基础上完成赢咖7注册的工作，那么纪要做好提前的准备工作，关注我们http://www.yuanmei168.com，了解更多！

This is the end of the analysis of the four working principles of the mixer. If you want to complete the work of the mixer on the basis of success and safety, make preparations in advance and pay attention to us http://www.yuanmei168.com , learn more!