1、开机前应仔细检查机械系统各部分，确认无误后方可开机。

1. Before starting the machine, carefully check all parts of the mechanical system and start the machine after confirming that there is no error.

2、启动前，应将操纵杆置于“空档”位置。

2. Before starting, put the control lever in the "neutral" position.

3、启动后，应将操纵杆置于“卸荷”位置，以排除筒内积水。

3. After startup, the control lever shall be placed in the "unloading" position to drain the accumulated water in the barrel.

4、装料时，操纵杆应置于“装料”位置。

4. When loading, the control lever shall be placed in the "loading" position.

5、运输前，卸料溜槽必须固定在“驱动”位置，防止摆动。

5. Before transportation, the discharge chute must be fixed in the "drive" position to prevent swing.

6、操作摇杆时，应在“空档”位置停留片刻，然后再移动到下一个位置。

6. When operating the rocker, stay in the "neutral" position for a moment, and then move to the next position.

7、做好文明施工，不要随意倾倒桶内多余的物料。卸料后，必须清洗搅拌筒、料槽、托辊等部位。

7. Do a good job in civilized construction and do not dump the excess materials in the bucket at will. After unloading, the mixing drum, material trough, idler and other parts must be cleaned.

8、当有人进入罐内混凝土结块时，应将车辆熄火，拔掉电动车门钥匙，并在罐外监控人员。

8. When someone enters the tank to remove the concrete caking, turn off the vehicle, pull out the electric door key, and monitor the personnel outside the tank.

9、将立柱上的功能切换开关，拨到“自动”位置，按下控制器上的启动开关，整个运行程序将自行自动控制运行。

9. Turn the function switch on the column to the "automatic" position, press the start switch on the controller, and the whole operation program will run automatically.

10、全过程运行完毕后自动停止，在运行工程中如需中途停机，可按下停止钮然后可重新启动。

10. It will stop automatically after the whole process is completed. If it is necessary to stop halfway in the operation project, you can press the stop button and then restart.

11、按下启动按钮后，显示屏即开始显示时间、慢速、加砂、快速、停止、快速、运行指示灯按时闪亮。

11. After pressing the start button, the display screen will start to display the time, slow speed, sanding, fast, stop, fast and operation indicators, which will flash on time.

12、自动控制时，必须把手动功能的开关全部拨到停的位置。

12. During automatic control, all switches of manual function must be turned to the stop position.

13、自动上料赢咖7注册应放在平放的位置，前后轴用方木垫好，使轮胎高空放置，以免起步时走动。

13. The automatic feeding mixer shall be placed in a flat position, and the front and rear axles shall be padded with square wood to place the tires at high altitude to avoid walking when starting.

14、赢咖7注册应实行二次漏电保护。上班前接通电源后，必须仔细检查，空车试转合格后方可使用。试运行时应检查搅拌筒的转速是否合适。一般来说，空车的速度比汽车（装载后）的速度略快2到3转。若相差较大，应调整主动轮与传动轮的比。

14. The mixer shall implement secondary leakage protection. After the power supply is connected before work, it must be carefully checked, and the empty vehicle can be used only after passing the test run. During trial operation, check whether the rotating speed of the mixing drum is appropriate. Generally speaking, the speed of an empty car is slightly 2 to 3 revolutions faster than that of a car (after loading). If the difference is large, the ratio of driving wheel to driving wheel shall be adjusted.

15、搅拌筒的转动方向应与箭头所指方向一致。如果不正确，则应更正电机接线。

15. The rotation direction of the mixing drum shall be consistent with the direction indicated by the arrow. If not, correct the motor wiring.

16、检查传动离合器、制动器是否灵活可靠，钢丝绳是否损坏，履带轮是否完好，周围是否有障碍物及各部位润滑情况等。

16. Check whether the transmission clutch and brake are flexible and reliable, whether the steel wire rope is damaged, whether the crawler wheel is intact, whether there are obstacles around and the lubrication of various parts.

17、自动上料赢咖7注册开机后要时刻注意赢咖7注册各部分运转是否正常。停机时要经常检查赢咖7注册的叶片是否弯曲，螺丝是否被敲落或松动。

17. After the automatic feeding mixer is started, always pay attention to whether all parts of the mixer operate normally. During shutdown, always check whether the blades of the mixer are bent and whether the screws are knocked off or loose.